Freemax Maxus 200W kit with M Pro 2 tank


Add to wishlist

Freemax Maxus 200W Kit with M Pro 2 Tank

Please Note : 2 x 18650 batteries are required (Not provided in the kit)


The Freemax Maxus is a 200W kit that is packed full of features not seen in any other mod. The Maxus 200W kit comes with the new and improved Mesh Pro 2 tank, correcting all the shortcomings of the extremely popular original Mesh Pro tank. 

Freemax Maxus Kit

Starting with the Maxus 200W mod, it is a double battery mod that requires 2 x 18650 high amp 18650 batteries (sold seperately) with a never before seen Smartload Technology. This allows you to put the batteries in with no predetermined polarity and the device would do the rest for you! The 200W mod is also capable of running on just a single battery although using the mod with dual batteries is highly recommended to fully unlock the capabilities of the Maxus 200W. Battery Charge is done through a Type C USB cable.

Freemax Maxus Smartload

The Freemax mod also has smart coil detection that automatically adjusts its mode based on the coil you are using. For example, should you put in a coil that is meant to run on temperature control, the device will detect this for you and change the settings on your behalf to "temperature control" if it was previously set on "power" and vice versa.

Display is done with a simple OLED screen to make the device more reliable compared to a complicated touch screen system and is also filled with safety features to ensure your device and you are well protected.

Maxus 200W Breakdown

The Mesh Pro tank was one of the most popular Direct to lung (DTL) tanks ever sold in our store and for good reason. It packed one of the most flavourful vape experiences you could have with pre-made coils and the new Mesh Pro 2 picks up where the mesh pro left of with significant improvements. Starting with the fill cap, a common issue that many people had with the Mesh pro tank was the top cap sliding open when in your pocket. It happens most often when left in your pocket while sitting down. We at Ace Vape Melbourne had to give away rubber rings for our customers facing that issue to allow for slightly more resistance to prevent the fill cap from sliding open too easily. With the new Mesh Pro 2, there was a fundamental redesign to increase the friction on the top cap to minimize potential leaks from the filler cap sliding open.

New M Pro 2 fill cap

The coils in the Freemax Mesh Pro 2 tank have also been given an updated from what they call the Coiltech 3.0 to the latest generation of the 4.0. The fundamentals of the coils are that the mesh which is military grade SS904L which basically means austenitic stainless steel is of extremely high quality and has very high levels of corrosion resistance. The cotton within the coil now utilises tea fiber cotton in 95% of the coil and 5% of organic cotton to bring you the best sub ohm vaping flavour on the market.

904L M Pro 2 coils

Tips on using the M pro 2

  1. For each new coil, fill the tank with your E liquid of choice. 70/30 VG/PG ratio is recommended as thinner liquids may cause leaking
  2. Close the cap and allow the tank to sit for a minimum of 10 minutes to allow the vape juice to absorb into the coil
  3. Give the tank 2 - 3 inhales before firing the coil for the first time to draw out any access air trapped in the coil.
  4. Check coil for recommended wattage range and program to mod accordingly
  5. Enjoy your the amazing flavour from your new favourite vape tank!

How to use M pro 2

Features and Specs for Freemax Maxus 200W kit

  • Smartload technology 
  • Single and dual battery compatible (Dual is recommended to unlock the mod's full potential)
  • 5-200W output
  • Power mode, VPC, Bypass, TC-TI, TC-SS, TC-NI, TCR modes
  • Type C USB Charging
  • 5ML Juice Capacity tank
  • Coiltech 4.0 Mesh coils
  • Upgraded slide to fill top cap

Protections and safety features

  • Open circuit protection
  • 10s time out protection
  • Overcharge protection
  • Low voltage protection
  • High temp protection
  • Short circuit protection
  • Low resistance protection
What comes in the kit
  • 1 x Freemax Maxus 200W Mod 
  • 1 x Freemax M pro 2 tank resin edition (Pre-installed M2 Mesh coil)
  • 1 x Freemax M1 mesh coil
  • 1 x 5ML replacement glass
  • 1 x Spare O-ring
  • 1 x USB Charging cable Type C
  • 1 x Warning card
  • 1 x Warranty card
  • 1 x User manual



Returns Policy

You may return most new, unopened items within 60 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).

You should expect to receive your refund within 1 week of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).

If you need to return an item, simply login to your account, view the order using the 'Complete Orders' link under the My Account menu and click the Return Item(s) button. We'll notify you via e-mail of your refund once we've received and processed the returned item.


We ship domestically across Australia.

If you place your order before 2PM, we will usually ship it out the same day (weekends excluded).

Orders under $60:
- Parcel Post (2-7 days): $7
- Express (Next day - to a major Australian city): $11
Note: We cannot ship batteries via Express. They will need to be sent via regular post.

Orders over $60
- Free Parcel (2-7 days)
- Express - $5
Note: We cannot ship batteries via Express. They will need to be sent via regular post.

Orders over $100
Free Express Shipping - Note: We cannot ship batteries via Express. They will need to be sent via regular post.